口述小姑两瓣湿乎乎_印度xxxxbbbb视频_掉出来可是要受到惩罚的_无码动漫性爽xo视频在线

Hotline:13924627849

Lasted News:

更多

Contact Us

Shenzhen Haolin Pml Precision Mechanism Ltd
Hotline:400-6846-806
Fax:0755-84196969
Tel:13924627849 (Mr.Hou)
Tel:18922863481 (Ms.Lai)
-mail:houlz@szhaolin.com.cn
Add:building 2, Huaguan Industrial Park, No. 63, Zhangqi Road, Guixiang community, Guanlan street, Longhua District, Shenzhen,china

Industry News

You are here:Home >> News >> Industry News
Dispenser operating procedure FAQ
Publish:電子產(chǎn)品全自動柔性組裝線,深圳市豪林精密機械有限公司  Time:2013-12-25
The most common problem encountered is the dispenser valve problems , to solve the following problem occurs when using plastic valves often an effective way .

One of the common problems process dispenser drip dispensing valve operation
1 After this happens often related to the completion of the dispensing valve .

2.95% of such cases are caused because the caliber of the needle used is too small.

3 small needles will affect the flow of the liquid causes back pressure , resulting in the formation of the phenomenon shortly after the completion of drip dispensing valve closed . The needle is too small will affect exhaust valve begins to bubble gum action when used as long as the replacement of a large needle to solve this problem.

4 backpressure tapered helical needle produces the least liquid flow most smoothly.

5 after the air within the liquid dispensing valve produces complete drip off phenomenon , it is best to preclude liquid air , or use of a bubble-containing gel is not easy . Centrifugation or gel first using the deaeration .

Two sizes of glue dispensing operation process inconsistencies FAQ
1 When the glue is inconsistent mainly for storage of fluid pressure cylinder or air pressure generated by instability .

2 meter inlet pressure regulator should be set at the lowest of low pressure over the factory 10 to 15psi., The pressure should be between the pressure tube using a pressure regulator above the middle of the table , you should avoid using a pressure gauge between being low pressure parts.

3 dispensing valve control pressure should be at least 60psi or more in order to ensure the stability of the plastic .

4 Finally, you should check out the glue time if less than 15 / 1000 seconds will cause the plastic instability . , Glue glue more time to grow more stable .

Three of the flow rate is too slow process of dispensing operations FAQs
1 If the flow rate is too slow pipeline should be from 1/ 4 "to 3/8 ."

2 If there is no need for the pipeline should be as short as possible .
3 In addition to change the tube , but also change the plastic mouth and pressure , so full speed up the flow rate.

Four bubbles within the fluid dispensing process operating FAQ
1 . Excessive fluid pressure if coupled with the valve open time is too short compared with the liquid may penetrate the air . Solutions to reduce the fluid pressure and the use of conical oblique needle .

       
2 V. glue dispensing operation of the process FAQ blocked.

3 such cases is mainly due to excessive moisture or repeated used instant glue . Be sure to use fresh, instant glue . The pipeline does not contain moisture Aceton with acetone thoroughly cleaned . After air drying for use should be determined between the plant and the installation of pneumatic valve system with plastic filter . ( If the above method does not work, you should use nitrogen ) .

Dispensing needle selection method :

1 . Four criteria : a small point - small needles, low- pressure , short-term high point - a large needle , greater pressure , longer concentrated glue - inclined needles, greater pressure , the time needed to set an aqueous liquid - small needles, small pressure needed to set the time .

2 . Fluids require special settings :

( 1 ) instant glue : water-based instant glue safe piston and Teflon -lined metal needles, for the thick of instant glue , use a tapered helical needle , For flexible use PP needle.

(2) UV glue : Use amber syringes, needles white piston and inclined (which can block ultraviolet ) .

( 3 ) light-curing adhesive: use black opaque syringes, white piston , the needle can block ultraviolet .

( 4 ) Anaerobic : Use 10CC syringes and white PE common piston .

( 5 ) and paste sealant fluid : If using white piston rebound serious , please use the security style living style , using oblique needle .
Previous:  2019/10/26
Next:Automatic Screw Machine FAQ  2013/12/25
国产午夜三级一区二区三区 | 别揉我奶头嗯啊一区二区三区 | 综合人妻久久一区二区精品 | 国产日产欧产精品精品视频 | 激情内射日本一区二区三区 | 日本高清VA在线播放 | 久久精品午夜91无码免费 | 欧美日韩一区二区2023 | 无码乱人伦一区二区亚洲 | 亚洲熟女综合一区二区三区 | 亚洲中文字幕在线5555 | 亚洲美女黄色网站观看大全 | 国产又色又爽又刺激在线播放 | 中文字幕乱妇无码AV在线 | 国产高清中文手机在线观看 | jj日本高清一区二区三区 | 久久久久国产精品嫩草影院 | 欧美人妻精品一区二区三区 | 中文字幕久久精品无码 | 麻豆天天躁天天揉揉AV | 国产午夜福利在线观看视频_ | 亚洲天堂中文字幕一区二区 | 2020亚洲无码在线观看 | 国产在线精品一区在线观看 | 中文字幕免费在线看线人动作大片 | 国产一级婬片永久免费看久久 | 国产人人干美女人人干美女呀 | 日韩美女赤裸网站一区二区三区 | 国产亚洲精品精品精品 | 最新国产自产视频在线观看 | 久久久WWW成人免费精品 | 中文字幕人成无码人妻 | 无码av中文字幕久久专区 | 亚洲毛片无码一区二区在线播放 | 精品人妻大屁股白浆无码 | 中文字幕在线免费看线人 | 大白P站欧美日韩中文字幕 国产一区二区三精品久久久无广告 | 亚洲中文字幕aV女同在线 | 久久午夜夜伦鲁鲁片无码免费 | 中文字幕无线码免费人妻 | 国内精品无码一区二区三区 |